Keeping you up to date with all things Rare Spares.

Rare Spares

Rare Spares Blog

  • Join Us on Facebook!
  • Visit Us on YouTube!
  • Follow Us on Instagram!
  • Subcribe to Our RSS Feed

History of the LS Engine

There’s a saying in the automotive world: “There’s no replacement for displacement.” Somehow, that tag became attached to an engine, in a vee shape and packing eight cylinders, made by Chevrolet in America. In the late nineties General Motors and Chevrolet debuted a new V8. Dubbed “LS” for “Luxury Sport” it’s this name and engine that have popularized the above saying. First seen in the 1997 C5 Corvette, the all “aluminum” block, called the LS1, was also known as the small block Gen111. It replaced the LT or “Luxury Touring” engine that had been a mainstay for some time. It was what’s called a clean sheet design; essentially a start from nothing design, the only common points the LS had with the LT was bore spacing and conrod bearings. Even in the LS range of engines themselves items such as the bore centre, at 4.40 inches, cross bolted six bolt main bearing caps, and a four bolt per cylinder head bolt pattern are common. Alloy blocks are used for performance oriented vehicles whilst blocks made of iron are used for SUVs and trucks. At 5.7 litres or 350 cubic inches in capacity, as the most common iteration is seen in, it produced 257 kilowatts or 345 horsepower. Maximum torque was 470Nm or 350 pound-feet, found at 4400rpm. It was bolted into a substantial range of cars such as the Corvette, Firebird, and of course in Holden and HSV cars like the Statesman and Senator Signature. LS6 is the name given to a higher output but same capacity engine largely found in the C5 Corvette Z06, with production starting in 2001. Peak grunt was bumped to 287 kilowatts and torque to 522Nm initially, with further development lifting both to 302kW and 540Nm. There were also smaller engines based on the same architecture. Engineered for use in passenger SUV and trucks, the LS1 4.8L and 5.3L blocks have a 3.78 inch diameter for the bore. In 2005 GM unveiled the GenIV or LS2 engine. There were bigger capacities, cylinder deactivation technology for improved fuel savings, and variable valve timing. Capacity went to 6.0L (5964 cc in real terms) or 364 cubic inches. Base engines made 300kW and 542 Nm. Holden and HSV saw this installed in cars such as the Monaro and Grange. L76 is the designation given to the LS2s fitted with Active Fuel Management or AFM. It was some time before Holden chose to use the feature; from 2009 it was installed however only in cars with an automatic called the 6L80. Power was rated as 260kW and maximum twist of 510 Nm came in at 4400rpm. Designed to assist in bettering fuel economy by shutting down firing in four cylinders, the engine gave rise to the L77. This designation defines the LS2 as being ethanol fuel compatible. Various engines with names such as LY5, LH6, and LMF were produced and seen in SUVs such as the Chevrolet Trailblazer and GMC Savana. LS7 was a rarely seen engine in Australia. It was intended to be produced for a specific HSV car here called the W427. Corsa Special Vehicles beat HSV to the punch here, with their engine producing 400kW and 600Nm. HSV’s version, first shown at the 2008 Melbourne International Motor Show, offered 375kW and 640Nm. A supercharged and slightly capacity increased engine, at 6.2L and called LSA, was released in 2009. This was first seen in the ballsy Cadillac CTS-V and Australia had it in the GTS, GTS-R, and Maloo R8 LSA, just to name a couple. 480kW was the peak power and an amazing 754Nm of torque. These came courtesy of a block with revised compression, cast pistons, and a “blower’ of 1.9L in capacity. With Holden ceasing local manufacturing in late 2017, the LS engines are now only to be found in cars already on Australian roads or in vehicles allowed to be imported from the US to Australia. For now….anyway. Stand by for Camaro. Keep in touch with Rare Spares and updates on our product range via our main website and for news and tips via the blog.

The Positives and Negatives of Buying at a Classic Car Auction

It’s an automotive enthusiast’s dream. Head to an auction that features a list of classic cars, the type that had you gazing at the poster on the wall for hours. Up for grabs is a Lamborghini Countach, perhaps a Tucker Torpedo, maybe even a classic Ford Model T. Niggling away is a question or two. How good will the car be? Why is it being sold? Let’s have a look at some of the ups and downs of buying such a machine at an auction. One immediate positive is that the prospective buyer MAY be the only person looking for a certain car listed. Sure, this easily can be a negative if everyone’s after a Ford Falcon GTHO with three hundred miles on the odometer but if it’s something like a 1957 Chevrolet Bel Air in reasonable condition, there’s a better chance of not so many eyes being on it. Many classic cars come with paperwork. This describes the history of the car from the day it was sold at a dealership, its service history in detail, any restoration work, and the canny owner will have had this done by specialists. As a result, the car should be in as close to showroom condition as possible and with as little to spend on top of the final purchase price. Reputable auction houses help behind the scenes by doing their best in ensuring a seller is not selling a dud. As an accepted rule, sellers via reputable auction houses are either known to the auction company through previous transactions, have been thoroughly vetted by investigation, or are a known vehicle investor. The classic car family is a solid and tightly knit network. One particular American gent has made a living from buying and restoring classic cars then selling them at auction. This, as a result, has had him build a great network of people to call for advice and for assistance when required. If car XYZ is missing part LMN then a phone call or email generally has someone somewhere saying “yes, I can help”. This results in being able to source a genuine part, just like Rare Spares offers as a service. However not all diamonds are polished. Although a good auction house will inspect the cars being offered for sale, sometimes human error creeps in and a car listed as 100% genuine may have parts that were hastily cobbled together from less than reputable sources to have it ready in time for sale. Thankfully these happenings are as rare as they can be. Cost at an auction is always the big question. Again, most reputable auction houses will be able to price the car to the market value. There will be a reserve, a minimum asking price, but sometimes that can work against buyers that feel the market is asking too much, or, conversely, can see the expected asking price soar way beyond expectations, leaving buyers frustrated with what could be seen as artificially inflating the value and therefore affecting similar vehicles negatively. Having a good knowledge of cars and the industry certainly won’t be seen as a bad thing. Not all rare cars are desirable and not all classic cars are expensive, so being able to research, shop around for the relative sales price of a car being eyed off will assist when you’re ready to buy. That way, at an auction and knowing what you’re prepared to spend will assist especially if there’s a choice of the car you’re aiming to purchase. Finally, an easily overlooked item: what are you, as a new buyer, going to do with the car itself? Some people are in an envious position to be able to store cars in a properly maintained environment and keep them as an investment. However if you’re looking to be a driver of the car, let’s say a Porsche 356 Speedster, what about: parts, fuel, insurance, the actual drivability of the car? Some classic car owners bring them out for car shows, perhaps a drive day at their local race track, and unfortunately too many are driven there and are trucked away with mechanical issues that weren’t obvious when bought. To use that well worn phrase, however, “at the end of the day” it shouldn’t be forgotten that a buyer of a classic car does so because they’ll ultimately wish to be happy, proud, satisfied, with their purchase. After all, that’s what Rare Spares aims for with our range of parts for Australian classic cars.  Let us know your thoughts on what you look for in a classic car and perhaps the good & the bad you’ve experienced at an auction. Keep up to date with our expanding product list at our website and stay in touch via our social media outlets.

Beginners Guide to getting into Motorsport – Part 2

In the first part of our article about how to enter motorsport, we finished with some hints about obtaining the relevant license to getting into entry level motorsport. There are those that have both the time and monetary resources to drive their private car in track days. And here, setting a budget to get into motorsport should not be overlooked. Generally no license is required for some of these but a waiver is required to be signed before going onto the tarmac. There’s cost effective Formula Ford, Formula Vee, and HQ Holden racing, even the Excel racing class. There are also regularity events, where a time is nominated and the car is driven on the track to try and meet, as best as possible, that nominated time. A minimum license requirement is here. And for many, this is as far as they may wish to go. There’s also a question of support. Not only does a prospective driver need to be aware that not always will there be obvious support, there may be, sadly, detractors that go out of their way to slow you down. However there are those that have just started their journey, taken another path, or have raced in numerous categories and now race competitively in events such as the Phillip island Classic. We spoke to three such drivers: karter Hugh Barter, respected motorsports commentator Greg Rust, and Rare Spares ambassador John Bowe. Greg Rust. Greg Rust, Rusty or Thrusta as he’s known, has the pleasure of being a motorsports commentator that’s come from a racing background. As is the case with so many, Rusty started off with go-karting, piloting an 80cc Tony kart. The powerplant came from Japanese motorbike maker Yamaha and had a manual transmission. Rusty says he remembers driving the little machine on the now gone Amaroo and Oran Park circuits, along with the existing Eastern Creek raceway track. However it was rallying that bit, and bit hard. Along with some pals from high school, a warmed over Mitsubishi Galant from the late 1970s was bought. Sporting some upgrades in the form of twin Weber carbies and a sports exhaust system, the car was entered at Supersprints at Amaroo, rallied in the western fringes of the Blue Mountains at Oberon and the beautiful Jenolan Caves area, and lead to some silverware being proudly displayed in the Rust home.Backing up the involvement with CAMS, Rusty says: “So I’m a BIG believer in joining a CAMS affiliated club. Get a license and, for not a lot of money really, you can get something for club competition. The best part is competing & socialising with friends around this kind of motorsport and tinkering in the garage on the car between events.” Rusty also points out that getting into motorsport is just the first step, but which way from there? There’s no doubt that driver training with experienced and qualified drivers will provide plenty of assistance but if there’s no goal to kick at, what can this training ultimately deliver? Rusty advises perhaps doing what Australian F1 driver Mark Webber did: lay out a plan to aim for the goal but look at paths to the side if that goal proves to be out of reach. Rusty himself followed those guidelines early in his racing and rallying career and is now “part of the furniture” when it comes to motorsport broadcasting. However starting at the bottom can take you into areas never thought possible. Greg is also an in demand host at corporate events and has a successful podcast. He says: “Finally you need good communication skills. Media Training is a must if you are serious. And you need to understand the business of the sport too. Be self starting. Work hard....bloody hard! And while the focus is what you do in the car, what you do out of it may end being where you spend the greater percentage of your time and it will prove instrumental in helping to open the right doors.”It’s crucial to note this final piece of advice. If you are looking to make a career out of motorsport, and the success comes from hard work, being able to deal with the media, such as Hugh, Greg, and John do, will need to be part of the plan. One bloke that knows both sides of the media fence is John Bowe. John Bowe. Our own Rare Spares ambassador John Bowe is a natural fit for anything to do with motorsport. Thanks to a career spanning thirty five years, “JB” is well placed for gaining insight into what a driver that wants to race should consider. John is well known not just for being a talented driver, but for his approachability and warm personality. It’s this latter point that John encourages in drivers wishing to be seen. John grew up in a family that already had ties to motorsport, however he pointed out that this can mean very little. Another well known Australian driver was mentioned and John asked him if his 11yo son had shown any interest in becoming a driver. The answer was “not really”. John uses this to point out any aspiring driver must have a love, a passion, for the sport. “I started racing because I loved it” says John. There were no plans at an early age to become a Formula 1 driver or Australian champion, he drove in motorsport because he loved it. John in no way discounts the natural ability in drivers, saying that there has been plenty he’s seen that are very, very, good, however the fire that got them to where they were was, in too many instances, extinguished because of a few speed-humps that had occurred. His point here was that in motorsport the balance between the good and the bad must be taken, and not to let some downsides override the passion that’s needed. Resilience is a key factor. Personality is one of JB’s strong points and this personality had one of the greats of Australian motorsport, Gary Cooper of Elfin fame, take John under his wing and provide some opportunities that may not have otherwise been available. JB was at pains to point that if this hadn’t occurred he would have been happy to have raced constantly in his home state of Tasmania due to his passion and love of motorsport and not have travelled overseas to race. John used this experience to highlight an easily overlooked factor for new drivers: coaching. Unlike a potential tennis champion, swimming champion, or golfer, motorsport doesn’t really have that one on one approach. Data acquisition and the ability to work with that, says John, in categories such as Formula Ford, is very important. But as to advice? John recalls one such situation at Perth’s Barbagallo Raceway, formerly known as Wanneroo Park. John was a relative rookie at the time and was campaigning with Larry Perkins. JB asked Perkins about which gear he was using in a particular corner. Larry’s advice was simple: “Go and try it for yourself.” This backs up John’s point about having that inner fire and desire. A unique point that John raised was about the European theatre. The home of Formula 1, there’s been numerous Australian drivers that have taken aim at cracking open the door to get a seat, however the burgeoning South East Asian race scene shouldn’t be overlooked for a driver’s overseas aspirations. John wrapped up his points by looping back to personality. This came in the context of marketability. John’s presence in the Australian motoring scene and his association with Rare Spares isn’t solely down to his driving history. By being a driver that is friendly, greetable and meetable, and is able to be media savvy and aware, such as the points Greg Rust raised, there’s a higher probability of overcoming perhaps the biggest single obstacle in Australian motorsport, the funds to go racing. JB says: “There’s no such thing as a free seat anymore.” Sponsors are looking to maximize exposure to their brand and a driver that’s looking to make a presence will have more chance of sponsorship and exposure. It’s easy to see that getting a foot in the door of Australian motorsport for a beginner driver isn’t complicated. But thanks to the input from three drivers at varying points in their career, a timeline for where you want that open door to take you is important, plans for where you may wish to go if the driving side doesn’t pan out need to be considered, and to take the good with the bad no matter your inherent ability can be crucial. A big thanks to Hugh Barter, Greg Rust, and Rare Spares ambassador John Bowe for their time and assistance.

Beginners Guide to getting into Motorsport – Part 1

Lowndes. Webber. Whincup. Schumacher. Vettel. Ricciardo. Drivers that are involved in the top levels of motorsport internationally and locally. They all have one other thing in common. They all started at the bottom of the ladder in the competitive driving sense. Around the world drivers of young ages are learning the basics of how to drive in motorsport. They may be in a basic single cylinder go-kart at their local outdoor track. They may be at a circuit listening in to their older brother or sister providing feedback on how the last drive in the Formula Ford or Formula Vee has gone. They could be an apprentice wielding the spanner in a team, talking to the driver of the Production Touring Car about how a change of shock absorber could help handling, or sitting in a seat, playing a race simulator in VR.  Thankfully, a huge bank balance isn’t required to get into the driver’s seat in motorsport. In Australia there are Superkarts with single and twin cylinder engines, Formula Ford and Formula Vee remain a strong and cost effective entry point, and even the venerable HQ Holden has a category at a budget per year that would pay for a team dinner in an F1 team.    But it’s not simply a matter of rocking up to a race track, strapping in, and going. CAMS have different entry methods including a temporary license for what’s called a “Come and Try Day”. They are a single use license and are designed to encourage those that wish to go further to progress to a higher qualification. Come And Try Days are perhaps the best form of path into motorsport purely because some people believe they’ll be fine behind the wheel on a dedicated racetrack. Another option is to try a session with a dedicated category. Formula Ford is recognized worldwide as the best path and in Australia there are quite a few options. There are companies that utilise race tracks to provide a driving experience and one example is Sydney Motorsport Park’s Formula Ford Experience. At varying costs a driver can start with five laps of the circuit, gaining experience and receiving tuition. Explanations on how the chassis works, the best points to brake and accelerate, are given by qualified instructors that more often than not are current or recently retired drivers. Crucial to getting on any race track is obtaining the appropriate license. CAMS suggest this for starters. There are two types of Level 2 licences - Non Speed (L2NS) and Speed (L2S). A L2NS licence entitles the competitor to compete in events such as observed section trials, touring assemblies, non-timed road events, motorkhanas, khanacross and drifting events, up to International level. A L2S licence entitles the holder to compete in L2NS events plus regularity trials up to National Championship level, single and multi-car speed events (not racing) up to International level, and touring road events that do not run over closed road sections. CAMS themselves are based in offices around the country and can be contacted from here: https://www.cams.com.au/ Some circuits also offer meetings where a potential official or driver can visit the track and meet people that are employed to work with and assist drivers. Sydney Motorsport Park runs such a program and is called Startline: https://www.sydneymotorsportpark.com.au/startline-by-ardc/ However, getting into a driver’s seat from an entry level point of view needs an entry level driver to explain more. In the second part of this look at entering motorsport, we’ll be talking to two more names that have had varying paths into motorsport. There’s the popular John Bowe, our Rare Spares ambassador, motorsport commentator and experienced competitive driver Greg Rust, but to kick off, here is a dedicated young driver and kart racer, Hugh Barter. Hugh Barter. It’s often said that to be the best driver, you have to be a young driver. Hugh Barter is an embodiment of this. Still a few months shy of his twelfth birthday, Hugh has more racing experience in a decade than many will have in a lifetime. This Japanese born talent first clapped eyes on something motorsport related at the age of three. Attending a V8 Supercars round at Victoria’s fabulous Phillip Island circuit, a racing simulator caught his attention. Minutes later, and with some assistance to help his small frame fit the setup, Hugh was belting around a simulated Mt Panorama. When Hugh had finished the crowd that had gathered applauded, knowing that something special had just happened under their very eyes. Flash forward a couple of years and young Barter, by way of a games console and driving rig, was ready to take the next step. A go-kart was a fifth birthday present and at the age of seven, a go-kart license was acquired. It’s here that Hugh’s entry experience offers up two different looks at the same end object. Hugh says that he gained a karting license and a CAMS backed license. Hugh joined an affiliated car club and registered with CAMS for the non speed license as mentioned in part one. This was, says Hugh, more cost effective than the alternate route taken, with a difference of nearly $800. Where Hugh follows the path that many successful drivers have driven is in setting out a timeline. With a clear hit rate in meeting his goals so far, Hugh’s eye to the future is on entering Formula Ford, with a move to Europe to race in Formula Renault penciled in as well. Next stop? Formula 1. Hugh’s well on his way to achieving that goal with consistently high levels of results from racing in the Cadet series in go-karts. Spread across Cadet 9 and Cadet 12 (age requirements),the karts Hugh had raced were these however he has moved into the next level, called Juniors with the age group of 12 to 16. The Cadets are small in size and engine output at 8hp, with the Junior’s specs capped at 11hp but are ideal for the age groups and provide theoretically equal performance. And it’s that last word that brings in another aspect of looking into entry level racing: sponsorship. Top end race drivers are covered in sponsorship thanks to their levels of performance, and here the budgetary aspects of motorsport dovetail with sponsorship. Not only will sponsorship help drivers like Hugh achieve their goals, it aligns companies with the sport itself which are then seen by prospective drivers. Stay tuned for the second part of this blog, which will be released in coming weeks. Head over to the Rare Spares Facebook page and tell us about your motorsport aspirations.

Targa Tasmania Event Wrap-up

Targa Tasmania has wrapped up its twenty seventh year and caps itself yet again as Australia’s premier tarmac rally series. It really is an event for any driver as there are ten distinct categories to choose from. There’s the Rookie Rallye, Vintage and Classic, Early Modern, and GT Sports Trophy, just to name a few. Combined with these categories is the ability to show up in approved cars that can date back to 1900. This year’s event was also round two of the CAMS 2018 Australian Targa Championship, with the first, Targa North West, also held in Tassie and is intended to give drivers a “taste” of the Targa Tasmania. The next events are Targa Great Barrier Reef before heading south to Victoria for Targa High Country. TT as some call Targa Tasmania, covers close to five hundred kilometers and is run across thirty-three special stages. The overall winners were once again Jason and John White in their Dodge Viper ACR. Jason and John have raced in twenty-one Targas, and have also moved into second place of the all time overall winners, sitting behind former Australian Touring Car Championship driver Jim Richards and long time ally and former V8 Supercars commentator, Barry Oliver. Oliver had also announced his retirement from motorsport prior to the event. The win placed the duo first in the Wrest Point GT2 class (cars made from January 2008 and two wheel drive, minimum 500 made). Second outright was a Subaru WRX STi, co-driven by Steve Glenney and Andy Sarandis. This had them win outright the RDA Brakes GT4 class (as per GT2, but with four/all wheel drive) and now lead the modern car section of the CAMS Targa Championship. Local honours were taken by Hobart doctor Michael Pritchard and co-driver Gary Mourant. They placed third outright in a Porsche and claimed second in the GT2 class. Former GT Championship driver Paul Stokell folded his lanky body into a Lotus Exige, one of many that competed and finished this year’s event, with co-driver Erin Kelly. The Whites were concerned about their tyres as co-competitors Matt Close and Cameron Reeves had been pushing them very hard prior to the final six stages. Jason White said: “We were actually having a lot more sweat about what was going on with the tyres. It really forced John and I to be at the top of our game.” Relief came for the Whites in the form of Close and Reeves’ Porsche GT3 losing traction on cold tyres and going off-road, damaging the car enough to stop further competitive driving. The third round of the CAMS Australian Targa Championship is the inaugural Targa Great Barrier Reef to be held in Cairns from August 31 to September 2.  Have you ever competed in Targa Tasmania? Or is it on your ‘bucket list’ to get down south and have a crack? Head over to the Rare Spares Facebook page and tell us all about it in the comments section below this article!

Rare Spares D’Alberto Car Collection

With great wealth comes great responsibility. That’s what Bill Gates said. He should know, having been one of the all time wealthiest people. But define wealth? Is it purely a monetary value? Or can it be a little philosophical and be of something untouchable, like the love a parent has for a child? Perhaps that wealth can be something others covet and envy. If it’s this, then the D’Alberto family certainly had wealth. This came in the form of a collection of motor vehicles that, in some cases, had barely a thousand kilometers worth of driving. The Echuca, Victoria, based family owned a car dealership group, spread across four locations in Victoria and New South Wales, and had amassed a considerable amount of cars over the past decades, including a 1927 Chevrolet ute, a 1927 Buick Tourer, a 1921 Model T Ford, and an absolute gem in the shape of a 1988 VL Walkinshaw Group A SS. Build number 333, if you don’t mind. Never registered it had still somehow covered some kilometers, but just 1308 of them. Part of the collection of cars that was auctioned off by Mildura based auction house Burns & Co, its new owner handed over $305,000 plus auction fees. The auction itself wasn’t just about moving rolling metal however. Plenty of boxes full of marketing material and posters were available, such as the evolution of Holden from the 1960s to the 1970s, Peter Brock and Holden Racing Team items, driving lights, user manuals for vehicles, trim pieces, and spare parts. It’d be fair to say, however, that it was the astounding collection of cars being offered that attracted the most eyeballs. Cars such as a 48/215, a Corvette Stingray, even a Sydney Olympic Torch Relay fitted out Commodore were there for the asking. A 48 year old LC Torana GTR went for an eyewatering $165,000, a similarly aged HT Monaro with a naturally aspirated 5.0L engine lightened the wallet for $170,00, while some more modern muscle in the form of a 1992 VN Group A SS saw $210,000 against its name. The D’Alberto brothers certainly had an eye for quality and made sure that as many as possible of the cars were in as best a condition as possible. Hence the responsibility part of the opening quote. A quick look through the online catalogue showcases shiny and well maintained cars, including a lovely 1970 Monaro GTS with a 186ci straight six cylinder. With the speedo reading just 313 miles travelled, it sold for $240,000. Do you have your own piece of Australian motoring history in your garage? Tell us about your pride and joy in the comments section on our Facebook page. Keep up to date with what’s happening in the world of Rare Spares by following us on social media, and by tracking news via our blog.

Rare Spares Holden Torana GTR-X Concept Car

Holden has a very strong history when it comes to designing and engineering concept cars. Of recent years there’s the immaculate Efijy, and the reborn Monaro. Both two door cars, interestingly enough, as two other concept cars were also two doors. There’s the Hurricane, and the Torana GTR-X. The latter came oh so close to being put into production, and the chassis itself was based on the LC Torana XU-1. The low slung, fibreglass bodied, slinky looking, machine even had the same engine, the then potent 186S. Exterior design was eye catching, with a long bonnet that started with a flat, shovel-like nose, pop up headlights, a steeply raked windscreen, and a sharp tail with hockey stick tail lights. These were design elements that were later seen in two of Italy’s best from Ferrari and Maserati. Inside the cabin featured laid back bucket seats, milled aluminuim sheeting, a plethora of gauges for oil temp and pressure and the like, and a short throw gear selector for the four speed manual. That was connected to the straight six which produced 119kW and 265Nm. They’re hardly groundbreaking numbers now but for a car built in 1970 that weighed under 1050kg, they provided more than enough punch. Unique at the time were the disc brakes to be found at each corner. It’s unclear exactly how many versions were built; some say three, some say four, but it’s known that just one example of what could have been an inspirational car survives. Holden has a museum at its Melbourne based headquarters, where the sole survivor lives in cosseted luxury. Why wasn’t it ever sold? The population of Australia in 1970 was just over twelve million and Holden’s numbers indicated that wasn’t enough to justify what would potentially be a low volume seller. Considering how well received the Datsun 240Z was when it was released just a year before, and how it’s perceived still after nearly fifty years, one could say this was a somewhat shortsighted view. Have you seen the Holden Torana GTR-X? What do you think of the car? Head over to the Rare Spares Facebook page and let us know in the comments section below.

Aussie Motorsport Classic: The Channel 9 Camaro

October 3, 1982. Reid Park, Mount Panorama, Bathurst. Lap 27. Kevin Bartlett. Camaro. A time, location and car that are forever etched into Australian motorsport history. KB is up with the leaders in the famous Bathurst 1000 when one of a batch of fourteen wheels the team had bought for the Camaro fails. It’s the rear left. Instantly, the tyre deflates, pitching the Channel 9 branded car’s rear into the concrete safety wall. The left front bounces off as the nose swings around and it’s just on a right hand curve on an uphill run. Unsettled, there’s momentum enough to cause the Camaro to roll over to the right, landing on its roof. The car skids to the other side of the track and quickly a trackside official is there to assist a shaken Bartlett out of the inverted Camaro. He’s ok, points at the clearly ruined wheel and tyre, and walks into the crowd. In context, it was a miracle that Bartlett and the Channel 9 sponsored car were in the race at all. In practice just a couple of days before, co-driver Colin Bond was at the wheel when a ball joint nut on the front left wishbone came adrift. The front left suspension collapsed and flung the corner into the wall. The location? Almost exactly where the wheel would fail two days later. As KB says: “it was a miracle that my crew and the TAFE smash repair team had it back together in time for qualifying.” However, there’s more to the story in getting the car on track in the first place. Bartlett bought the car, a brand new 1978 built machine, from an American dealership and imported the car into Australia. The intent was to race it in what was then the Group C regulations. Once the car landed, Bartlett says, a lot of work was needed to get the car down to the weight as stipulated. The leaf spring suspension was replaced with fibreglass units, super strong Kevlar for the front guards and spoilers, but CAMS insisted that the car use drum brakes at the rear, instead of the optional disc brakes. In case you’re wondering why the car looks different to a 1978 model, it’s because CAMS also said the car had to run with bodywork from the ’74 to ’77 models. Bartlett still shakes his head in disbelief. But there was a hidden benefit as it turned out. The earlier bumpers were aluminium, not steel… Is the Channel 9 Camaro your favourite Aussie Motorsport classic? Or maybe you're a GTHO or Torana sort of person? Head over to the Rare Spares Facebook page and tell us about your favourite cars to hit the Australian motorsport scene!

David Ryan’s FX Holden Build

In this week’s Rare Spares Blog we will be taking a look at a project car close to the heart of Rare Spares Director David Ryan. It would be fair to say that David has an affinity with old Holdens, more specifically 1950’s FX’s and FJ’s, having owned numerous of the early Aussie classics and having raced them across the country and overseas! David has recently been able to purchase back one of his old Variety Club Bash cars, and has an ambitious plan laid out for it to be completely restored by Christmas 2018 for a special occasion – his granddaughter Chloe’s wedding! The 1953 FX in question has had anything but an easy life, let’s take a look! In 1953, David’s father, uncle and a mate decided to take part in the REDeX  Around Australia Reliability Trial using a black 1953 FX Holden taken from the fleet of the family taxi service and used for the event. Upon its return it was reinstated to the rank to serve out its days once again as a cab.   In 1986, David, and some mates decided to take part in the famed Variety Club Bash event using an EH Holden setup specifically for offroad racing. Officials deemed the car was too fast and not suitable for this sort of event, hence a more suitable replica of the original FX was decided to be built for their next foray into the Bash the following year. The work undertaken to build the replica FX was completed by David and his mates utilising the converted bus depot that was at that stage the premises of the fledgling Rare Spares organization.  David’s father was kept in the dark on the build until the time of unveiling, when one day he drew back the garage doors to unveil the pristine replica of his beloved REDEx machine.     In 1990, the FX was sold and David was left to focus on his many other ongoing projects. These included competing in the 1993 London to Sydney Marathon in a HK Monaro, taking an Aussie 1946 Chev ute street rod to the US and a trip to Mexico to compete in the 2013 La Carrera Panamericana, a 3200km open road event, racing a 1954 FJ! You can read about this incredible restoration and event here Over the past decade David was in regular if not frequent contact with the owner asking if the FX would ever be available to buy back. The once loved car was languishing in a suburban backyard, dying a slow and rusty death, with the new owner unwilling at that time to part with it.. Fast forward to early 2018, David was searching through some online early Holden forums where low and behold, his FX was listed as possibly coming up for sale! A quick phone call was made to the owner to re-express his interest.     After a week or two of negotiating back and forth, the car is now back in David’s hands and plans are well underway for a complete restoration to be finished by December for Chloe’s wedding. With an abundance of options for her wedding car, one would think Chloe would go for something a little more luxurious. However, with the FX once again back in the hands of her grandfather, there was only one car Chloe had in mind! The car is now in Adelaide where it is being paint stripped and rust treated, this is due to be completed by mid next week. From there extensive rust repair will be undertaken before being baked, primed and painted by a good friend. The seats will be re-trimmed in their original colour (red) all while a full mechanical refurbishment will be undertaken. The 132ci grey motor, 3 speed transmission, differential and suspension will all be rebuilt to stock specifications. We will be paying close attention to the FX Holden build, so stay tuned for further updates as 2018 progresses! What are your memories of the early 1950s Holden’s? Did you or someone you know own one? Head over to the Rare Spares Facebook page and let us know about it in the comment section below!

Phillip Island Classic Preview

Movies, songs, popular culture, motor sport. What do they have in common? Yup, it’s obvious, they all have something to do with time, specifically “the past”. But why should motor sport be involved in what happened, not what’s coming? The Victorian Historic Racing Register doesn’t really care because they know that the Phillip Island Classic, to be held over the ninth to the eleventh of March 2018, pulls people to the picturesque Phillip Island race circuit in droves. There’s something a bit extra special about this meeting. Along with a strong presence of members of the Group S racing family, the weekend will commemorate fifty years of Formula 5000 racing and with over thirty five sparkling examples of these thunderous machines expected. Legendary Australian touring car driver John Bowe will be in attendance and on the Sunday will showcase a 1974 March ex F1 car. He’ll be with fellow racer and noted collector Guido Belgiorno-Nettis in a Ferrari F1 car formerly raced by Italian driver Michele’ Alboreto. Both will be racing these historic machines against two younger drivers that have years of experience between them already, Tom Tweedie and Tim Berryman. The categories include the smaller and fascinating Formula Ford and Formula Vee, Groups Q and R, and pre WW2 cars in the Group J and some Group K, with post WW2 cars in Group K also. WW2 itself will be represented, in a motor racing sense, with the inclusion of Group L, a category for cars built between 1941 and 1960. These cars are those built especially for competition, be they factory backed or one-offs. There’s a sub-category in the Ls, known as “square riggers”. These are primarily MG TCs sans mud guards, windscreens, and headlights. But people don’t attend historic motorsport events such as this to just and merely goggle over the eye watering range of cars on track and on display. There are the personalities in attendance such as the aforementioned JB. This weekend will also have five patrons there. Better known as “KB”, one of Australia’s most loved drivers, Kevin Bartlett, a two time winner of the Australian Drivers’ Championship and a Bathurst 1000 winner, will be on deck. Alfredo “Alfie” Constanzo, an Italian born, Australian raised, driver, a four time Australian GP competitor and four time Australian Drivers’ Championship winner, is there. Alan Hamilton, who won the Australian Sports Car Driver award twice ,and along with Alfie is a four time winner of the Gold Star Championship, is slated to appear. Two time New Zealand Grand Prix winner John McCormack, who also won the Australian Drivers’ Championship three times, is scheduled to be there. And New Zealand’s MBE awarded driver Ken Smith, won the New Zealand Grand Prix in 1976, 1990 and in 2004 and raced Formula Ford, Formula 5000, Formula Pacific, Formula Mondial and Toyota Racing Series. Ken has competed over 59 consecutive seasons on the motor racing circuit. He has won the Gold Star Drivers Award five times, Formula 5000 Revival three times, the Penang Grand Prix three times, the Selanger twice and the Malaysian Grand Prix once. In 1995 Ken was inducted into the New Zealand motorsport Hall of Fame. Australian cars of note will be there. An Australian Grand Prix winning (Frank) Matich A50 and an MR8 Elfin 5000 campaigned in the US by Garrie Cooper and Vern Schuppan will be on track. Rare Spares ambassador for eleven years, JB says of the event, “it’s the second best race track in Australia and there’ll be 550 classic cars at this weekend’s Classic.” John drove three cars in 2017 and for 2018 says: “I’ll be driving something that’s very rare, an Allard J2X from 1952 owned by Carroll Shelby that had raced in the American sports car scene.” This will be the first time this car has competed in Australia. John acknowledged the support of his good friend Joe Calleja, current owner of the Allard, including the opportunity to drive his 1969 Group N Mustang. Of Rare Spares JB said:” Without Rare Spares there would not behalf of the Aussie classic cars on the road that there is now.” John mentioned a recent club meeting he attended along with his great mate Dick Johnson and just how many cars were there that had used Rare Spares. John’s relationship with the Phillip Island Classic goes back to 2000, and he’s driven a range of cars and 2000 first event, covering range of cars including a Le Mans style car to a 1970’s Porsche. John invites all Rare Spares attendees and fellow car enthusiasts to come and say hi! Are you heading down to the Phillip Island Classic? Or have you been in years past? Head over to the Rare Spares Facebook Page and tell us your experiences in the comments section below.